North Georgia Metals

...

Kevlar Gloves

For protection while handling metal materials.

...

Tie Downs (Set)

Four per set.

...

Tie Downs (Heavy Duty)

One per set

...

Bending tool

Used to put the hem on an edge detail for architectural panels (gables, eaves, and valley detail)..

...

Drip Edge Folding Tool

Used for quick bends in standing seam panel edges. Makes up to 1 1/2" (38.1 mm) deep bends along drip edge of roofing panel.

...

12" Folding Tool

Folds edges of aluminum siding, Trim coil and lighter gauges of sheet metal up to 26 gauge.

...

1/4” Magnetic Socket

Used for woodgrip screws.

...

5/16” Magnetic Socket

Used for self-driller screws.

...

Metal Cutting Blades

As compared to using an abrasive wheel, you’ll obtain: 1) less noise 2) fewer blade changes 3) no burr on edges 4) drastically reduced sparking 5) less cost per cut 6) faster cutting 7) cool cutting. Available in 48 and 56 tooth models.

...

AV3 Snips

Aviation style steel metal snips for straight cuts and slightly curved cuts in either direction. Straight, Left, and Right Cutting application with yellow handle.

...

AV6 Snips

Aviation style steel metal snips for straight cuts and slightly curved cuts in either direction. Left Cutting application with yellow handle.

...

AV7 Snips

Aviation style steel metal snips for straight cuts and slightly curved cuts in either direction. Right Cutting application with green handle.

...

M2003 Snips

Cuts Superior material flow and lower profile allows maximum maneuverability. Fast adjusting, long life pivot bolt and nylon locking nut with pressure washer holds desired adjustment even for repetitive use in heavy gauge metal. The ergonomic grip maximizes power stroke of hand while the classic grip has the fit and feel of tradition. Tips of jaws ground to point allows access in tight quarters. Straight, Left, and Right cutting application.

...

M2005 Snips

The Max 2000 Bulldog Aviation Snip designed for notching and trimming.

...

M2006 Snips

The serrated upper jaw of the Max2000 Offset Snip offers solid gripping power with less burr. Ground tips on jaws allow access in tight areas, so that Max Offsets can easily make nickel size blind hole cuts. A full 1-1/4" cutting plane offset from handles makes trim cuts with the Max2000 Offset both accessible and efficient. Cuts sharp left angles.

...

M2007 Snips

The serrated upper jaw of the Max2000 Offset Snip offers solid gripping power with less burr. Ground tips on jaws allow access in tight areas, so that Max Offsets can easily make nickel size blind hole cuts. A full 1-1/4" cutting plane offset from handles makes trim cuts with the Max2000 Offset both accessible and efficient. Cuts sharp right angles.

...

MC12A Snips

Sleek styling, easy blade replacement and larger handles make the Andy™ Snip more versatile. A sleek head design improves maneuverability. Ideal for making cuts in tight material, shapes such as J-Channel. A full 3" (76.2 mm) cutting length makes straight shearing with the Malco Andy™ Snip fast and easy. Blade replacement is easily accomplished in the field.

...

MC12NG Snips

Sleek styling, easy blade replacement and larger handles make the Andy™ Snip more versatile. A sleek head design improves maneuverability. Ideal for making cuts in tight material, shapes such as J-Channel. A full 3" (76.2 mm) cutting length makes straight shearing with the Malco Andy™ Snip fast and easy. Blade replacement is easily accomplished in the field.

...

MV12

Cut through heavy vinyl siding lockseams and more with ease! This unique Andy combination snip design features a knife-like cutting edge to produce a smooth slicing action for easy one-hand operation. The user simply grasps the snip with the red grip up for optimal blade alignment when making straight cuts or left or right circular cuts in a variety of non-ferrous materials including: layered components of heavy-grade vinyl siding and aluminum trim coil. Please note that the versatile Andy MV12 Snip is NOT FOR CUTTING STEEL.

...

2" Hand Seamer

The serrated upper jaw of the Max2000 Offset Snip offers solid gripping power with less burr. Ground tips on jaws allow access in tight areas, so that Max Offsets can easily make nickel size blind hole cuts. A full 1-1/4" cutting plane offset from handles makes trim cuts with the Max2000 Offset both accessible and efficient. Cuts sharp right angles.

...

3" Hand Seamer

Precise vee-notched depth graduations on jaws are in 1/4" (6.4 mm) increments. Jaws are drop forged, high impact steel. Hardened steel handles resist abuse. Powerful compound leverage design. Tool also features rust resistant nickel plating. Non-slip vinyl grips with hand stops provide added comfort and control.

...

6" Hand Seamer

Wide 6" jaws produce uniform, accurate bends in sheet steel and non-ferrous metals with greater control and efficiency. Wider jaws also minimize buckling and bowing of metal. Fewer strokes are required to bend and straighten angles. Designed for all the metal trades, including HVACR installation, roofing and siding applications and commercial building and remodeling.

...

Straight Seamer & Tongs

Precision ground jaws with beveled nose produces 135-degree bends. Ideal for precise metal fabricating including HVAC and Metalworking Specialist trade applications.

...

Straight Seamer & Tongs (Gripped Jaws) (SG10)

Non-marring, vinyl-gripped jaws are ideal for bending and seaming painted metals including soffit and fascia and metal roofing.

...

Metal Edge Roller

The Malco Edge Roller No. MRER makes clean precise bends along the edge of standing-seam metal roofing or metal building panels.

...

25' Measuring Tape

Malco’s “MAGNETIC TIP” TAPE MEASURE is ideal for every ferrous metalworking project! Use it for HVAC ductwork installations, ceiling grid applications, metal stud framing and more. A powerful magnet and self-supporting 1” wide blade makes 1-person measurements and measuring elevations an easy task. The magnetic tip and big standout blade can even be used as a pick-up tool! A double riveted tip connection, abrasion-resistant, nylon coated blade and rubber-clad housing and blade stop assure lasting performance.

...

30' Measuring Tape

Malco’s “MAGNETIC TIP” TAPE MEASURE is ideal for every ferrous metalworking project! Use it for HVAC ductwork installations, ceiling grid applications, metal stud framing and more. A powerful magnet and self-supporting 1” wide blade makes 1-person measurements and measuring elevations an easy task. The magnetic tip and big standout blade can even be used as a pick-up tool! A double riveted tip connection, abrasion-resistant, nylon coated blade and rubber-clad housing and blade stop assure lasting performance.

...

Turbo Shear

The TURBOSHEAR Model No. TS1 inserts directly into the chuck of a standard 1200 rpm A/C or cordless drill.Cuts straight and to the left and is capable of navigating tight curved patterns and squares in heavy 20-gauge (1.02 mm) galvanized steel. Blind cuts require only a 1/2”(12.7 mm) starting hole. Cutting applications include both ferrous and non-ferrous sheet metals, metal roofing/building panels, vinyl, steel mesh, ductwork, even the thick metal of furnace jackets, equipment enclosures or automotive body panels. An offset design keeps both hands away from work surface. Long-wearing hardened jaws are also replaceable.

...

Turbo Shear Heavy Duty

The TurboShear HD cuts straight and to the left and makes fast cuts in material thickness up to 18-gauge galvanized steel. Cutting applications include both ferrous and non-ferrous sheet metals, metal roofing/building panels, vinyl, steel mesh, and ductwork.

...

Hand Riveter

Four rivet nosepieces: 3/32", 1/8", 5/32", and 3/16" store in handle. Suited for riveting applications in gutter and downspouts. Not for use with 5/32" or 3/16" steel rivets (steel rivets larger than 3.2 mm). Spring return handles and comfortable contour grip make operation fast and easy.

...

Crimper (3 blade)

Ideal for crimping heavy 24 to 22 gauge (0.71 to 0.86 mm) galvanized sheet steel. Nickel plating and vinyl grips.

...

N2 Notcher

The N2 Notcher punches a big 1 inch (25.4 mm) deep “V” notch in common 24 to 30 (0.71-0.41 mm) gauge galvanized sheet metal quickly and easily.

...

SRT2

SideSwiper model SRT2 combines the comfort and added leverage of an easy-to-grasp straight handle with the smooth unlocking motion of a burr free hook. The blade of the SRT2 is angled from the bottom plane of the handle and allows the user to keep the wrist straight while keeping knuckles well above the work. Blade surface finishing and plating assures that the sharply angled hook will not cut into the vinyl material or produce shavings.

...

TNP2S

Heavy Duty Trim Nail Punches Drive trim nails into soffit, fascia and other finishing trim without denting or marring material. All-steel nose and aluminum tail piece directs weight of this punch to the working end when grasping or starting a nail. Accommodates up to 1-1/4" (31.2 mm) standard trim nails. Nose fits into 1/2" (12.7 mm) J channel.

...

Shingle Remover

Shingle removal is a beast of a job but now, finally, there’s a tool that’s up to the task. THE BEAST Shingle Remover from Malco makes a tough job bearable. THE BEAST cleanly lifts off heavy loads of shingles and pulls nails in one motion. All long handled BEASTS feature replaceable 10 gauge (3.40 mm) tempered steel blades with variable length teeth. A comfortable D-grip is also standard.

...

Shingle Remover (Adjustable Head)

Shingle removal is a beast of a job but now, finally, there’s a tool that’s up to the task. THE BEAST Shingle Remover from Malco makes a tough job bearable. THE BEAST cleanly lifts off heavy loads of shingles and pulls nails in one motion. This model comes with an adjustable head for handling any roof pitch. All long handled BEASTS feature replaceable 10 gauge (3.40 mm) tempered steel blades with variable length teeth. A comfortable D-grip is also standard.

...

Safety glasses

Protective eyewear, recommended when working with metal materials.

...

Caulk Gun

Small and lightweight caulking gun